1 files changed, 142 insertions, 0 deletions
diff --git a/config/includes/mouse_tp.dtsi b/config/includes/mouse_tp.dtsi
new file mode 100644
index 0000000..52856ca
--- /dev/null
+++ b/config/includes/mouse_tp.dtsi
@@ -0,0 +1,142 @@
+#ifdef HAS_MOUSE_TP
+  #include <dt-bindings/zmk/mouse_settings.h>
+
+ /*
+  * Key Behaviors to adjust settings
+  */
+
+  // They key codes below can be used to adjust the TP settings at runtime
+  // without needing to recompile the firmware.
+  //
+  // The values will be logged and saved in the config on the controller flash
+  // after 60s (CONFIG_ZMK_SETTINGS_SAVE_DEBOUNCE).
+  //
+  // On boot the settings will be restored again.
+  //
+  // If you prefer a more explicit way of configuration, you can also hardcode
+  // these settings in `&mouse_ps2`.
+  //
+  // If you set these settings in `&mouse_ps2`, you will still be able to
+  // adjust the values during runtime with these key codes, but after
+  // restarting the board the values in `&mouse_ps2` will be restored and not
+  // the ones stored in the flash using the key codes.
+
+
+  // How sensitive the trackpoint is
+  #define U_MSS_TP_S_I &mms MS_TP_SENSITIVITY_INCR
+  #define U_MSS_TP_S_D &mms MS_TP_SENSITIVITY_DECR
+
+
+  // The maximum speed the trackpoint will accelerate to
+  #define U_MSS_TP_V6_I &mms MS_TP_VALUE6_INCR
+  #define U_MSS_TP_V6_D &mms MS_TP_VALUE6_DECR
+
+
+  // I am not quite sure tbh... default seems fine.
+  #define U_MSS_TP_NI_I &mms MS_TP_NEG_INERTIA_INCR
+  #define U_MSS_TP_NI_D &mms MS_TP_NEG_INERTIA_DECR
+
+
+  // How hard you have to press to activate the "Press To Select" feature that
+  // lets you tap or press on the trackpoint to click.
+  //
+  // Not all trackpoints support it and you have to enable
+  // `tp-press-to-select;` in `&mouse_ps2` first.
+  #define U_MSS_TP_PT_I &mms MS_TP_PTS_THRESHOLD_INCR
+  #define U_MSS_TP_PT_D &mms MS_TP_PTS_THRESHOLD_DECR
+
+
+  // If you mess up the settings, you can use this key code to clear the
+  // settings from flash and re-set the default values on the TP.
+  //
+  // Make sure to wait at least CONFIG_ZMK_SETTINGS_SAVE_DEBOUNCE seconds (60
+  // by default) before restarting the board to ensure the settings are
+  // written to flash storage.
+  #define U_MSS_RESET   &mms MS_RESET
+
+
+  // If you prefer to set the settings in `&mouse_ps2`, you can use the key
+  // codes above to find the settings you like the most and then press this
+  // key code to output the settings to the log.
+  //
+  // Then you can add those values to `&mouse_ps2`
+  #define U_MSS_LOG     &mms MS_LOG
+
+
+ /*
+  * Driver-specific configuration
+  */
+
+  &mouse_ps2 {
+    // Enables scroll wheel on mouse devices supporting the Intellimouse
+    // extension.
+    // scroll-mode;
+
+
+    // Disables clicking. Useful when using a PS2 driver that is prone to
+    // erros in transmissions to reduce accidental clicks.
+    // disable-clicking;
+
+    // The frequency at which the mouse samples and sends data (in hz).
+    // The default rate is 100. You can try lowering it if you experience
+    // connection errors.
+    //
+    // Higher values than 100 are no improvement in my experience, but will
+    // increase battery life and potentially errors in transmissions.
+    //
+    // These values are allowed: 10,20,40,60,80,100,200
+    // sampling-rate = <60>;
+
+
+    // Enable clicking by tapping on the TP. Not all TPs support this.
+    // tp-press-to-select;
+    // tp-press-to-select-threshold = <10>;
+
+
+    // How sensitive the TP is (Default: 128)
+    tp-sensitivity = <135>;
+
+
+    // The maximum mouse movement speed the TP will accelarate to (Default: 97)
+    tp-val6-upper-speed = <182>;
+
+
+    // Not quite sure what it does tbh :) (Default: 6)
+    tp-neg-inertia = <6>;
+
+
+    // Adjusts axis settings on the TP
+    // Works only on some trackpoints, but may be properly considered by the
+    // trackpoint's acceleration features (which may or may not have an
+    // impact). Alternatively consider achieving the same effect using the
+    //  `zmk,input-configs` feature.
+    // tp-xy-swap;
+    // tp-x-invert;
+    // tp-y-invert;
+
+  };
+
+ /*
+  * Input Config
+  */
+
+  &mouse_ps2_config {
+    xy-swap;
+    x-invert;
+    y-invert;
+
+    // Set the layer that should automatically activate when the mouse is
+    // moving.
+    layer-toggle = <MOUSE_TP>;
+
+    // How long the mouse needs to move for before the layer is activated (to
+    // avoid accidental activations while typing) (Default: 250)
+    layer-toggle-delay-ms = <250>;
+
+    // How long to wait, after the last mouse movement, before deactivating
+    // the layer (Default: 250)
+    layer-toggle-timeout-ms = <250>;
+  };
+
+
+#endif